components product information connector new 1/8 mb-0111-5 november 2006 jae pmk div. proprietary. copyright ? 2006 japan aviation electronics industry, ltd. features dd1 series 0.5mm pitch stroke connector co nforming to usb2.0 standard general specifications ? no. of contacts : 30 pos. ? contact resistance: 50m ohm max. (initial) ? dielectric withstanding voltage : dc500v per minute ? insulation resistance: 1,000m ohm min. (initial) ? enhanced twisting resistance at mating/ unmating through equipping a guide rail ? secure ground connection for emi prevention ? conforms to transmission s pecified in usb2.0 standard ? pb free receptacle ? occupied volume on chassis was consid ered at design and small package was achieved. ? available in standard and reverse mounting type to re spond to various mounting situations. ? hot-plug structure ? available on embossed tape for automatic mounting cradle ? available in two types. angle type, which expands cradle designi ng capacity, and tilted type, slanted at a 75 degr ee angle to the board. ? 13.8mm depth was achieved, which enable s minimizing the occupied area on pcb ? alignment guide structure: guide range of 1.0mm min. (receptacle ? cradle) ? angle type available on embossed tape for automatic mounting. tilted type available in exclusive tray. plug ? side-lock type ? simple part structure enables simple wire termination. ? standard cable diameter 5.0mm. cables with other diameters can also be applied. ? rated current: for signal 0.5a for power 1.0a ? rated voltage: ac 30vr.m.s ? operating temperature: -25 deg. c to +75 deg. c ? mating cycle: 10,000 times the dd1 series of connectors are single -line rectangular i/o connectors with 0.5mm pitch stroke conforming to usb2.0 standard. [plug] [receptacle] [cradle] angle type tilted type rohs compliant reverse type standard type
mb-0111-5 2/8 jae pmk div. proprietary. copyright ? 2006 japan aviation electronics industry, ltd. materials and finishes components materials/ finishes contact copper alloy/ contact: au plating over ni terminal: au flash plating over ni insulator glass filled nylon resin shell stainless steel/ sn plating over ni receptacle components materials/ finishes contact copper alloy/ contact: au plating over ni terminal: au flash plating over ni insulator glass filled nylon resin shell stainless steel/ main frame: ni plating through-hole: sn plating over ni through-hole plate copper alloy/ main frame: ni plating through-hole: sn plating over ni cradle components materials/ finishes contact copper alloy/ contact: au plating over ni terminal: au flash plating over ni insulator glass filled nylon resin shell stainless steel/ ni plating hood glass filled polycarbonate/ color: black lock spring stainless steel/ ni plating clamp barrel copper alloy/ ni plating bushing pvc/ color: black plug
mb-0111-5 3/8 jae pmk div. proprietary. copyright ? 2006 japan aviation electronics industry, ltd. ordering information dd1 -r 030 h a 1 plating specification a: contact area: au plating: 0.1um min., terminal area: au flash plating connection type h: with hold down, j: without hold down no. of contacts: 30 pos. series r: receptacle modification code 1: standard mounting type, 7: reverse mounting type dd1 -b 030 h a 1 plating specification a: contact area: au plating: 0.1um min., terminal area: au flash plating connection type h: with hold down, v: 75 degree tilted type no. of contacts: 30 pos. series b: cradle modification code receptacle cradle dd1 -p 030 m a 1 plating specification a: contact area: au plating: 0.1um min., terminal area: au flash plating connection type m: soldered to cable no. of contacts: 30 pos. series p: plug modification code plug hold-down through-hole boss dd1r030ha1 2 2 2 sj100601 dd1r030ja7 - 4 2 sj106061 dd1b030ha1 2 4 2 sj100602 dd1b030va1 - 6 - sj102068 dd1p030ma1 - - - sj100603 part number board anchoring method jacs-3285 sj drawing specification
mb-0111-5 4/8 jae pmk div. proprietary. copyright ? 2006 japan aviation electronics industry, ltd. sj drawing no.: sj100601 receptacle: dd1r030ha1 applicable bo ard dimension (for reference) unit: [mm] pattern prohibited area (dimension of mating area)
mb-0111-5 5/8 jae pmk div. proprietary. copyright ? 2006 japan aviation electronics industry, ltd. sj drawing no.: sj106061 receptacle: dd1r030ja7 applicable bo ard dimension (for reference) unit: [mm] pattern prohibited area (dimension of mating area)
mb-0111-5 6/8 jae pmk div. proprietary. copyright ? 2006 japan aviation electronics industry, ltd. unit: [mm] note 1: this drawing shows a disposable backup board to keep connector and board in position during mounting. applicable board dime nsion (for reference) sj drawing no.: sj100602 cradle: dd1b030ha1 pattern prohibited area (dimension of mating area)
mb-0111-5 7/8 jae pmk div. proprietary. copyright ? 2006 japan aviation electronics industry, ltd. drawing when mated (for reference) applicable bo ard dimension (for reference) sj drawing no.: sj102068 cradle: dd1b030va1 unit: [mm] pattern prohibited area (dimension of mating area)
mb-0111-5 8/8 jae pmk div. proprietary. copyright ? 2006 japan aviation electronics industry, ltd. japan aviation electroni cs industry, limited product marketing division aobadai building, 3-1-19, aobadai, meguro-ku, tokyo 153-8539 phone: +81-3-3780-2787 fax: +81-3-3780-2946 notice: products shown in this leaflet are made for the applications listed below. however, if the above-mentioned prod ucts are to be used in aerospace devices, marine cable-connection devices, atomic power control systems, medical equipment for life-support systems, or any other specific application requiring extremely high reliability, please contact jae for further information. recommended applications: computers, office machines, measuring devices, telecommunication devices (terminals, mobile devices), av devices, household applications, fa devices, etc. sj drawing no.: sj100603 plug: dd1p030ma1 unit: [mm] * the specifications in this brochure are subject to change w ithout notice. please contact jae for information. note) the plug is shipped in plug only. exclusive crimp tool ct150-6-rh07 (applicable cable diameter 5.0 mm) is needed for wire connec tion and assembly. please contact us for other cable diameters and further information. (dimension of mating area) (dimension of mating area) 6
|
